GeekVape Aegis Legend 2 | 200 Watt L200 Kit

The latest offering from GeekVape is an updated look back on one of its best-selling devices. The Legend 2 is a sleeker and lighter version of the original tough mod. Still resistant to what you can throw at it,  the Legend 2 now has an easier way to lock your device on the go. A-Lock is a new feature that puts a switch on the side of the device to quickly lock your device for those times when you need it. Complete with a 1.08-inch screen, flipping port cover, and the GeekVape Z sub-ohm tank. 

Features:



Parameters
Battery: dual 18650 batteries (not included)
Output: 5-200W
Output Voltage: Max 12V
Output Current: Max 45A
Resistance range: 0.1-3Ω
Screen: 1.08 inch TFT color display
Charging Port: Type-C Port
Low voltage warning: 3.2V±0.1V
PCBA Temperature alarm: 80℃
Longest vaping time: 10s
Stand-by current: < 10uA
Operating temperature: 0℃- 45℃
Storage temperature: - 20℃-60℃
Relative humidity: 45%RH-75%RH

Packages



1x Aegis Legend 2 mod
1x Z Sub ohm Tank 2021 (5.5ml)
2x Geekvape Z Series coil(Pre-installed: 0.2Ω 70-80W; Spare: 0.25Ω 45-57W)
1x Coil Tool
1x Type-C cable
1x Spare glass tube(5.5ml)
1x Spare parts

INSTRUCTIONS of Geekvape Aegis Legend 2 Kit

Prompts: 
①Anti-reverse battery protection. (Reverse battery connection does not damage chip)
②While the resistance of tank≤0.08ohm, the device prompts short circuit for 2s. ③While the resistance of tank≥3.5ohm, the device prompts high resistance for 2s.
④Single battery voltage < 3.2v before use or < 2.8v during use, the device will stop output automatically and prompt low voltage for 2s.
⑤When the temperature of circuit board >65*C before use or >85°C during use, the device prompts high temperature for 2s.
⑥No atomizer: press the fire button, the device prompts no atomizer for 2s.
⑦Single output is over 10s timeout, the device stops output and prompts timeout for 2s.
⑧In the locked state, press the "+" or“-”button to adjust the Parameters, the device prompts screen lock for 2s.

Resistance lock: When the cursor is toggle to the resistance value of coil, press the "-" button to lock/unlock the resistance value, press the "_" button to update resistance value and unlock.

New atomizer: 
①In the standby interface, it will monitor whether the atomizer is replaced and update the latest atomizer resistance.
②When a new atomizer is inserted, the screen will jump to the interface for selecting new and old atomizer and prompt the user to select new and old atomizer.
③Click the"+" key to select the new atomizer, and click the "_" key to select the old atomizer.
④When the original atomizer is removed, the resistance value will be automatically cleared.

Bypass mode: The constant output voltage is 4.15V. The power does not exceed 200W.

Geekvape Aegis Legend 2 Features

1. Geekvape Aegis Legend 2 is smaller and lighter than Aegis Legend
2. Geekvape Aegis Legend 2 added Accidental Press Protection. A-Lock, a new way to protect from accidents.
3. Geekvape Aegis Legend 2: screen display, Features "Waterproof, Dustproof ， Shockproof" have been upgraded
4. Geekvape Aegis Legend 2 using Type C, not USB; Charging port with flipping cover, easier to fuel your vape.
5. Geekvape Aegis Legend 2 fixed problem: Battery door is a little hard to close
6. Geekvape Aegis Legend 2 has larger Air Slots
7. Airflow Adjustable and Fill Liquid is different between 2 matching tanks, Geekvape Z Sub-ohm Tank 2021, the best leakproof tank so far.

The adjustments for the device are as follows:
*Five clicks of the fire button turn the device on/off
*Three clicks of the fire button to enter settings mode
*One-click of the fire button in settings mode moves the cursor to select parameters
*Up and down to change parameters
*Long press the fire button to exit settings mode
*Up and down to change wattage or temperature
*Up and down at the same time to lock the screen
*Fire and down at the same time to decrease brightness
*Fire and up at the same time to increase brightness
*Fire and up and down at the same time for stealth
*Three clicks of the fire button then hold both up and down to change color 

Paramaters PK.